Home - Return to Previous Page
Ford Ranger Hawk HPS Brake Pads - HB279F594
HB279F594
HPS - High Performance Street Brake Pads
Superior Stopping Power
HPS - High Performance Street disc brake pads are world renowned for increasing stopping power on your street legal vehicle. Increasing the performance of your vehicles braking system is easy when you choose Hawk Performance's HPS braking compound. This unique Ferro-Carbon formula was developed for street performance using the safety and quality of Aerospace and Motorsports severe-duty friction technology.
The High Performance Street compound offers a higher coefficient of friction over stock brake pads and can provide you 20-40% more stopping power and higher resistance to brake fade than most standard replacement pads. Less fade means you'll have a highly durable brake pad with less brake dust..
HPS Ferro-Compound Features:
Increased stopping power High friction/torque hot or cold Gentle on rotors Extended pad life Low dust Virtually noise-free
All Hawk Performance High Performance Street brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.
Note:
Hawk Performance burnishes its High Performance Street brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against.
Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
Superior Stopping Power
HPS - High Performance Street disc brake pads are world renowned for increasing stopping power on your street legal vehicle. Increasing the performance of your vehicles braking system is easy when you choose Hawk Performance's HPS braking compound. This unique Ferro-Carbon formula was developed for street performance using the safety and quality of Aerospace and Motorsports severe-duty friction technology.
The High Performance Street compound offers a higher coefficient of friction over stock brake pads and can provide you 20-40% more stopping power and higher resistance to brake fade than most standard replacement pads. Less fade means you'll have a highly durable brake pad with less brake dust..
HPS Ferro-Compound Features:
All Hawk Performance High Performance Street brake pads provide a limited lifetime warranty, ensuring products to be free of defects from manufacturer's workmanship and materials.
Note:
Hawk Performance burnishes its High Performance Street brake pads as a final step in the factory, but all brake pads have to be bedded-in with the rotors (new or used) that they will be used against.
Properly bedding-in new brake pads results in a transfer film being generated at the pad and rotor interface to maximize brake performance.
Was:
$91.99
Sale:
$79.99
Save:
13%
Save:
$12.00
Description
20-40% More Braking Power!
Available in Front Pads
Fits: 1987-1994 Ford Ranger
Available in Front Pads
Fits: 1987-1994 Ford Ranger
Installation
Ford Aerostar Hawk HPS Brake Pads - HB279F594 Fits:
1987-1997 Ford Aerostar
Brake Pad Installation Procedure
1. Install brake pads properly. Be sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess wear and tear.
4. Check disc for proper thickness, parallelism, and lateral runout.
5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.
6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.
7. Inspect calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions
1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.
2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.
3. Be sure to not drag brakes!
4. Allow 15 minutes for brake system to cool down.
5. After step 4 your new pads are ready for use.
1987-1997 Ford Aerostar
Brake Pad Installation Procedure
1. Install brake pads properly. Be sure pads are securely positioned in the caliper.
2. Flush system with fresh brake fluid.
3. Check all hydraulic parts for excess wear and tear.
4. Check disc for proper thickness, parallelism, and lateral runout.
5. Check disc for scoring or grooves over .012"depth. If either applies, resurfacing is required.
6. If discs do not need resurfacing, then contamination from the previous brake pads must be removed. Sand discs with 130 grit sandpaper using moderate pressure. Use soap and water to clean discs' surface after sanding and machining. Discs should be free and clear of oil, grease, and brake fluid.
7. Inspect calipers for freedom of movement. Lubricate where necessary.
Burnishing Instructions
1. After installing new brake pads, make 6 to 10 stops from approximately 30-35 mph applying moderate pressure.
2. Make an additional 2 to 3 hard stops from approximately 40 to 45 mph.
3. Be sure to not drag brakes!
4. Allow 15 minutes for brake system to cool down.
5. After step 4 your new pads are ready for use.
Details
- HB279F594
- HB279F594
- Hawk
- New
Categories
Shipping Information
- Item Requires Shipping
- $24.99